A mid-century outdoor wall lantern should look intentional in daylight and still read clearly after dark. This 23.6-inch fixture does both: a copper or bronze body, a rectangular water-glass panel held by removable buckles, an E27 socket, and a three-step color temperature switch you operate from an ordinary wall switch. If the spot beside your front door needs one tall architectural lantern rather than a pair of small sconces, this is the profile to start with.
Design and materials: what you are actually buying
The body is copper with a tempered glass shade — not stamped steel with a painted finish. That matters for two reasons. Copper develops a patina over time rather than flaking, and tempered glass carries the visual weight the mid-century silhouette needs. The shade is a water-pattern panel: subtly rippled, so light spreads softly and the bulb itself stays hidden from eye level.
Two finishes are offered, bronze and copper. Bronze sits quieter against brick, stone, and dark siding; copper reads warmer and holds up as a deliberate accent on white or cream facades. Both share the same rectangular glass and the same straight arm, so the choice is purely about how much attention you want the fixture to draw.
One practical detail worth noting before purchase: the glass is retained by removable buckles. Bulb replacement means releasing the buckles and lifting the panel — no unscrewing an entire frame or disassembling the arm.
Where this lantern works best
The proportions drive placement. At 7.9 inches wide, 8.7 inches deep, and 23.6 inches high, this is a vertical fixture. It is designed to flank a door, mark a gate, or punctuate a stretch of blank exterior wall — not to line up in a tight row of six.
- Single-door entry: one lantern on the latch side, or a matched pair if the door is centered and wide.
- Garage and side entries: a single unit reads well where a symmetric pair would feel crowded.
- Balconies and terraces: the downward throw keeps glare out of seated sightlines.
- Courtyards and villas: repeated along a colonnade or garden wall at generous spacing.
The stated illumination area is 54 to 161 square feet (5.0 to 15.0 m²). Treat that as a range, not a promise — a clear E27 bulb at higher output lands near the top of it, a decorative filament bulb near the bottom.
Three color temperatures, one ordinary switch
This is the feature that separates the fixture from a plain lantern. Color temperature is selectable in three steps — 3000K, 4500K, and 6000K — cycled through your existing wall switch. No app, no hub, no separate remote on the hardwired version.
Be clear about what it is and is not. This is color temperature switching, not brightness dimming. Brightness adjustment is not supported. If you need true dimming, plan on a dimmable bulb plus a dimmer at the switch, and accept that this fixture’s own control is limited to the three color steps.
| Setting | Appearance | Reasonable use |
|---|---|---|
| 3000K | Warm white | Residential entries, porches, hospitality-style exteriors |
| 4500K | Neutral white | Mixed residential/commercial facades, walkways |
| 6000K | Cool white | Security visibility, garages, service entries |
In practice, most homes will set 3000K and leave it. Reach for 4500K when the facade is pale stone or the surroundings are heavily lit, and 6000K only where you genuinely want the crisper, whiter look.
Specifications
| Dimensions | 7.9″ W x 8.7″ D x 23.6″ H (20.1 x 22.1 x 59.9 cm) |
| Weight | 8.81 lb (4.0 kg) |
| Material | Copper body, tempered glass shade |
| Finish options | Bronze, Copper |
| Light source | E27, changeable, bulb included |
| Color temperature | 3000K / 4500K / 6000K, 3-step switch |
| Brightness dimming | Not supported |
| Voltage | 110V |
| Power supply | Hardwired, or hardwired/solar |
| Ingress protection | IP65 |
| Illumination area | 54–161 sq ft (5.0–15.0 m²) |
| Smart features | None |
| Certification | UL, ETL, CE, RoHS, FCC |
| Care | Wipe clean with a dry cloth |
Hardwired or solar: which version to order
Both versions are hardwired at the fixture — the difference is whether a solar power option is built in. The practical split:
- Choose hardwired if there is already a switched junction box at the location and you want constant, weather-independent output. This version ships without a remote.
- Choose the solar option if running new cable is expensive or impossible — a brick pier, a freestanding garden wall, a gate column. This version includes a remote control and adds light-control as well as remote operation.
Solar output depends on daily sun exposure at the panel’s position. A shaded north wall or a deep overhang will underperform no matter what the panel rating says, so verify sun hours before committing.
Installation: height, spacing, and bulb choice
Three numbers do most of the work.
Height. A common convention for an entry lantern is to center it roughly 66 to 72 inches above the threshold or grade — high enough to clear heads, low enough that the glass panel sits near eye level. With a 23.6-inch fixture, check that the top of the lantern still clears any transom or header detail.
Spacing. When repeating the fixture along a wall or colonnade, spacing of roughly 8 to 12 feet between units keeps the rhythm readable without turning the facade into a runway. Odd counts usually look better than even ones on long walls.
Reach. The 8.7-inch depth means the lantern projects meaningfully from the wall. Confirm clearance from swinging doors, shutters, and gutter downpipes before drilling.
On bulbs: the socket is standard E27 and the bulb is included, so the fixture works out of the box. If you swap it, stay within the fixture’s rated voltage (110V) and pick a bulb rated for enclosed or damp outdoor use. A larger globe fills the water-glass panel more completely; a slim filament bulb leaves more visible glass and a more period-correct look.
Living with copper and glass outdoors
IP65 means dust-tight and protected against water jets — appropriate for exposed exterior walls, porches, and balcony installations. Coastal installations are workable given the copper body and tempered glass, but salt air is aggressive on any metal. Wipe the fixture with a dry cloth on a regular schedule; the description specifies dry cleaning, not wet washing.
Expect copper to change. That is the material behaving correctly, not a defect. If you want the finish to stay uniform, plan on more frequent cleaning; if you want the patina, leave it alone.
FAQ
Is this outdoor wall lantern dimmable?
It offers 3-step color temperature switching at 3000K, 4500K, and 6000K, operated by an ordinary switch. Brightness dimming is not supported by the fixture.
What are the exact dimensions?
7.9″ wide x 8.7″ deep x 23.6″ high (20.1 cm x 22.1 cm x 59.9 cm), weighing 8.81 lb (4.0 kg).
Does the solar version come with a remote?
Yes. The solar power option includes a remote control; the hardwired option does not.
Can it be used in a coastal area?
The copper construction, tempered glass, and IP65 rating make it suitable for coastal environments. Regular cleaning is recommended to maintain appearance.
How do I change the bulb?
Release the removable buckles holding the water-glass panel, lift the panel, and replace the E27 bulb. No full disassembly is required.
The short version
Buy this lantern if you want a tall, narrow, mid-century form with real copper and tempered glass, a color temperature you can change from the wall switch, and a choice between hardwired and solar power. Skip it if you need dimmable brightness, smart-home control, or a compact sconce — none of those are what this fixture is.
See the Mid-Century Outdoor Wall Lantern in copper or bronze →



